- Efficient Spraying Necessary to Reduce Drift and Increase Output
- By Dr. Andrew Landers
Cornell University
- Disease and insect control is a critical factor on most commercial farms. Whilst such control may, in some seasons, be a small proportion of crop value, there is a demand from growers for increased efficiency of spraying. Attention to detail is necessary to improve efficiency of deposition, reduce drift and increase sprayer output.
A grower on Long Island, N.Y. stated that drift management is all in the mind; it requires the grower to think about reducing drift before the legislators apply controls.
Spray drift of pesticides is an important and costly problem facing pesticide applicators. Drift results in damage to susceptible off target crops, environmental contamination to watercourses and a lower than intended rate to the target crop, thus reducing the effectiveness of the pesticide.
Pesticide drift also affects neighboring properties, often leading to concern and debate. As more people choose to live in the picturesque setting of the countryside and growers continue to sell plots to increase their revenue, so the debate will continue.
There are two types of drift - airborne drift, often very noticeable and vapor drift. The amount of vapor drift will depend upon atmospheric conditions such as humidity, temperature and the product being applied and can occur days after an application is made. Drift is influenced by many inter-related factors including droplet size, nozzle type and size, sprayer design, weather conditions and last but not least the operator.
Droplet
In the past, crops were drenched with high volumes and coarse droplets at up to 50 gallons per acre resulting in plants dripping with excess pesticide. The belief that too much is better than too little is misplaced. Dripping crops lead to environmental pollution such as soil contamination and an excessive number of tank loads per acre results in poor time management.
Lower volumes must be used which may result in smaller droplets although there is a limit to droplet size because of concerns about drift. Droplets under 150 microns generally pose the greatest hazard; droplets less than 50 microns have insufficient momentum for impaction as they remain suspended in the air indefinitely or until they evaporate.
The higher the operating pressure, the smaller the droplet; conversely, low pressure produces large droplets that may bounce off the target. Certain spray surfactants can change the droplet spectrum, reducing the number of driftable droplets.
Nozzle Type and Size
Modern nozzle technology such as air inclusion nozzles produce larger droplets than conventional cone nozzles. Large droplets normally roll off the leaf but air inclusion nozzles create air bubbles within the larger droplets, which then collapse on contact with the leaf, dissipating the energy and dispersing the liquid. Recent research in the grape industry in Western New York has shown promising results using air inclusion nozzles to control grass weeds.
Rotary atomisers create smaller, more uniform droplets, which would normally drift. When used in conjunction with a tower and cross flow fan design the smaller droplets are actually directed into the canopy. This type of sprayer, referred to by some as controlled droplet application, produces 95-98% of its droplets all of the same size.
Sprayer Design
Air-sleeve booms are better at targeting the spray into the canopy, reducing drift and increasing deposition. Shields can vary from the simple to the complex, fitted with flat fan nozzles or controlled droplet applicators using reduced herbicide rates. Shielded sprayers allow growers to apply herbicides in variable weather conditions.
Sprayer Calibration
Correct calibration will ensure that all the nozzles are discharging the correct amount of liquid at the correct distance and angle to the target and at the correct forward speed. Operators must set the air deflectors correctly to confine airflow, spray and disturbance to the canopy.
Weather
Wind speed and direction, relative humidity, temperature and atmospheric stability affects drift. Applying the correct product to the correct target at the correct time with the correct equipment is the key to good spraying.
Research in England and New Zealand has measured the effectiveness of shelterbelts. Natural and artificial belts were used and drift is reduced the closer you are to the shelterbelt. Shelterbelt height and density will affect drift, and may, in certain conditions, create additional air currents and eddies. There are so many variables such as topography and wind direction that it is difficult to conclude that research at one site is transferable to another.
Choose the correct size sprayer with good back-up support to ensure that spraying may be done in a timely manner. Far too often growers are racing around in an attempt to apply pesticides after a problem disease or insect attack has occurred. Good logistical support in reducing the need to return for frequent refills is so important. The use of field cards, detailing the block, pesticide required, application rate, quantity required per tank fill etc. will reduce stress levels found amongst some applicators. IPM should also be considered. “Forward planning is the key to good management;” a phrase often used by successful business managers also applies to farm management.
Continuing development of spray application techniques will improve the efficiency of crop spraying. Many of the factors which affect application and drift are interdependent. Crop canopies and water volumes must be carefully considered if growers are to take advantage of new technologies.
Strategies to Reduce Drift
Before spraying:
1. Train the operator to use the sprayer correctly on your farm under your conditions.
2. Plan the spraying operation; consider the use of field cards as a good management tool.
3. Read and follow the pesticide label.
4. Select the correct nozzle for the target.
5. Consider the use of sprayers, which direct the spray to the target.
6. Consider spray additives to reduce drift.
7. Improve spraying logistics to ensure adequate time to spray within ‘ideal’ conditions.
8. Only spray when weather conditions are ideal.
9. Calibrate the sprayer with water to ensure that everything is working correctly.
10. Start planting windbreaks!
During spraying:
11. Stay alert: ensure the spray is not allowed to drift on to non-target areas and watch for changes in wind speed and direction.
12. Keep spray pressure as low as possible and ensure an accurate gauge is used.
13. Maintain a constant speed and pressure, if an automatic regulator is fitted. Remember, small increases in speed result in large increases in pressure.
14. Avoid spraying near sensitive crops or water courses; use a buffer zone.
Note: Where trade names, manufacturers or distributors names appear, no discrimination is intended and no endorsement by the author or Cornell University is implied.
